| /* |
| * tpm_tis.c - QEMU's TPM TIS interface emulator |
| * |
| * Copyright (C) 2006,2010-2013 IBM Corporation |
| * |
| * Authors: |
| * Stefan Berger <stefanb@us.ibm.com> |
| * David Safford <safford@us.ibm.com> |
| * |
| * Xen 4 support: Andrease Niederl <andreas.niederl@iaik.tugraz.at> |
| * |
| * This work is licensed under the terms of the GNU GPL, version 2 or later. |
| * See the COPYING file in the top-level directory. |
| * |
| * Implementation of the TIS interface according to specs found at |
| * http://www.trustedcomputinggroup.org. This implementation currently |
| * supports version 1.21, revision 1.0. |
| * In the developers menu choose the PC Client section then find the TIS |
| * specification. |
| */ |
| |
| #include "sysemu/tpm_backend.h" |
| #include "tpm_int.h" |
| #include "block/block.h" |
| #include "exec/address-spaces.h" |
| #include "hw/hw.h" |
| #include "hw/i386/pc.h" |
| #include "hw/pci/pci_ids.h" |
| #include "tpm_tis.h" |
| #include "qemu-common.h" |
| #include "qemu/main-loop.h" |
| |
| /*#define DEBUG_TIS */ |
| |
| #ifdef DEBUG_TIS |
| #define DPRINTF(fmt, ...) \ |
| do { fprintf(stderr, fmt, ## __VA_ARGS__); } while (0) |
| #else |
| #define DPRINTF(fmt, ...) \ |
| do { } while (0) |
| #endif |
| |
| /* whether the STS interrupt is supported */ |
| #define RAISE_STS_IRQ |
| |
| /* tis registers */ |
| #define TPM_TIS_REG_ACCESS 0x00 |
| #define TPM_TIS_REG_INT_ENABLE 0x08 |
| #define TPM_TIS_REG_INT_VECTOR 0x0c |
| #define TPM_TIS_REG_INT_STATUS 0x10 |
| #define TPM_TIS_REG_INTF_CAPABILITY 0x14 |
| #define TPM_TIS_REG_STS 0x18 |
| #define TPM_TIS_REG_DATA_FIFO 0x24 |
| #define TPM_TIS_REG_DID_VID 0xf00 |
| #define TPM_TIS_REG_RID 0xf04 |
| |
| /* vendor-specific registers */ |
| #define TPM_TIS_REG_DEBUG 0xf90 |
| |
| #define TPM_TIS_STS_VALID (1 << 7) |
| #define TPM_TIS_STS_COMMAND_READY (1 << 6) |
| #define TPM_TIS_STS_TPM_GO (1 << 5) |
| #define TPM_TIS_STS_DATA_AVAILABLE (1 << 4) |
| #define TPM_TIS_STS_EXPECT (1 << 3) |
| #define TPM_TIS_STS_RESPONSE_RETRY (1 << 1) |
| |
| #define TPM_TIS_BURST_COUNT_SHIFT 8 |
| #define TPM_TIS_BURST_COUNT(X) \ |
| ((X) << TPM_TIS_BURST_COUNT_SHIFT) |
| |
| #define TPM_TIS_ACCESS_TPM_REG_VALID_STS (1 << 7) |
| #define TPM_TIS_ACCESS_ACTIVE_LOCALITY (1 << 5) |
| #define TPM_TIS_ACCESS_BEEN_SEIZED (1 << 4) |
| #define TPM_TIS_ACCESS_SEIZE (1 << 3) |
| #define TPM_TIS_ACCESS_PENDING_REQUEST (1 << 2) |
| #define TPM_TIS_ACCESS_REQUEST_USE (1 << 1) |
| #define TPM_TIS_ACCESS_TPM_ESTABLISHMENT (1 << 0) |
| |
| #define TPM_TIS_INT_ENABLED (1 << 31) |
| #define TPM_TIS_INT_DATA_AVAILABLE (1 << 0) |
| #define TPM_TIS_INT_STS_VALID (1 << 1) |
| #define TPM_TIS_INT_LOCALITY_CHANGED (1 << 2) |
| #define TPM_TIS_INT_COMMAND_READY (1 << 7) |
| |
| #define TPM_TIS_INT_POLARITY_MASK (3 << 3) |
| #define TPM_TIS_INT_POLARITY_LOW_LEVEL (1 << 3) |
| |
| #ifndef RAISE_STS_IRQ |
| |
| #define TPM_TIS_INTERRUPTS_SUPPORTED (TPM_TIS_INT_LOCALITY_CHANGED | \ |
| TPM_TIS_INT_DATA_AVAILABLE | \ |
| TPM_TIS_INT_COMMAND_READY) |
| |
| #else |
| |
| #define TPM_TIS_INTERRUPTS_SUPPORTED (TPM_TIS_INT_LOCALITY_CHANGED | \ |
| TPM_TIS_INT_DATA_AVAILABLE | \ |
| TPM_TIS_INT_STS_VALID | \ |
| TPM_TIS_INT_COMMAND_READY) |
| |
| #endif |
| |
| #define TPM_TIS_CAP_INTERRUPT_LOW_LEVEL (1 << 4) /* support is mandatory */ |
| #define TPM_TIS_CAPABILITIES_SUPPORTED (TPM_TIS_CAP_INTERRUPT_LOW_LEVEL | \ |
| TPM_TIS_INTERRUPTS_SUPPORTED) |
| |
| #define TPM_TIS_TPM_DID 0x0001 |
| #define TPM_TIS_TPM_VID PCI_VENDOR_ID_IBM |
| #define TPM_TIS_TPM_RID 0x0001 |
| |
| #define TPM_TIS_NO_DATA_BYTE 0xff |
| |
| /* local prototypes */ |
| |
| static uint64_t tpm_tis_mmio_read(void *opaque, hwaddr addr, |
| unsigned size); |
| |
| /* utility functions */ |
| |
| static uint8_t tpm_tis_locality_from_addr(hwaddr addr) |
| { |
| return (uint8_t)((addr >> TPM_TIS_LOCALITY_SHIFT) & 0x7); |
| } |
| |
| static uint32_t tpm_tis_get_size_from_buffer(const TPMSizedBuffer *sb) |
| { |
| return be32_to_cpu(*(uint32_t *)&sb->buffer[2]); |
| } |
| |
| static void tpm_tis_show_buffer(const TPMSizedBuffer *sb, const char *string) |
| { |
| #ifdef DEBUG_TIS |
| uint32_t len, i; |
| |
| len = tpm_tis_get_size_from_buffer(sb); |
| DPRINTF("tpm_tis: %s length = %d\n", string, len); |
| for (i = 0; i < len; i++) { |
| if (i && !(i % 16)) { |
| DPRINTF("\n"); |
| } |
| DPRINTF("%.2X ", sb->buffer[i]); |
| } |
| DPRINTF("\n"); |
| #endif |
| } |
| |
| /* |
| * Send a request to the TPM. |
| */ |
| static void tpm_tis_tpm_send(TPMState *s, uint8_t locty) |
| { |
| TPMTISEmuState *tis = &s->s.tis; |
| |
| tpm_tis_show_buffer(&tis->loc[locty].w_buffer, "tpm_tis: To TPM"); |
| |
| s->locty_number = locty; |
| s->locty_data = &tis->loc[locty]; |
| |
| /* |
| * w_offset serves as length indicator for length of data; |
| * it's reset when the response comes back |
| */ |
| tis->loc[locty].state = TPM_TIS_STATE_EXECUTION; |
| |
| tpm_backend_deliver_request(s->be_driver); |
| } |
| |
| /* raise an interrupt if allowed */ |
| static void tpm_tis_raise_irq(TPMState *s, uint8_t locty, uint32_t irqmask) |
| { |
| TPMTISEmuState *tis = &s->s.tis; |
| |
| if (!TPM_TIS_IS_VALID_LOCTY(locty)) { |
| return; |
| } |
| |
| if ((tis->loc[locty].inte & TPM_TIS_INT_ENABLED) && |
| (tis->loc[locty].inte & irqmask)) { |
| DPRINTF("tpm_tis: Raising IRQ for flag %08x\n", irqmask); |
| qemu_irq_raise(s->s.tis.irq); |
| tis->loc[locty].ints |= irqmask; |
| } |
| } |
| |
| static uint32_t tpm_tis_check_request_use_except(TPMState *s, uint8_t locty) |
| { |
| uint8_t l; |
| |
| for (l = 0; l < TPM_TIS_NUM_LOCALITIES; l++) { |
| if (l == locty) { |
| continue; |
| } |
| if ((s->s.tis.loc[l].access & TPM_TIS_ACCESS_REQUEST_USE)) { |
| return 1; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static void tpm_tis_new_active_locality(TPMState *s, uint8_t new_active_locty) |
| { |
| TPMTISEmuState *tis = &s->s.tis; |
| bool change = (s->s.tis.active_locty != new_active_locty); |
| bool is_seize; |
| uint8_t mask; |
| |
| if (change && TPM_TIS_IS_VALID_LOCTY(s->s.tis.active_locty)) { |
| is_seize = TPM_TIS_IS_VALID_LOCTY(new_active_locty) && |
| tis->loc[new_active_locty].access & TPM_TIS_ACCESS_SEIZE; |
| |
| if (is_seize) { |
| mask = ~(TPM_TIS_ACCESS_ACTIVE_LOCALITY); |
| } else { |
| mask = ~(TPM_TIS_ACCESS_ACTIVE_LOCALITY| |
| TPM_TIS_ACCESS_REQUEST_USE); |
| } |
| /* reset flags on the old active locality */ |
| tis->loc[s->s.tis.active_locty].access &= mask; |
| |
| if (is_seize) { |
| tis->loc[tis->active_locty].access |= TPM_TIS_ACCESS_BEEN_SEIZED; |
| } |
| } |
| |
| tis->active_locty = new_active_locty; |
| |
| DPRINTF("tpm_tis: Active locality is now %d\n", s->s.tis.active_locty); |
| |
| if (TPM_TIS_IS_VALID_LOCTY(new_active_locty)) { |
| /* set flags on the new active locality */ |
| tis->loc[new_active_locty].access |= TPM_TIS_ACCESS_ACTIVE_LOCALITY; |
| tis->loc[new_active_locty].access &= ~(TPM_TIS_ACCESS_REQUEST_USE | |
| TPM_TIS_ACCESS_SEIZE); |
| } |
| |
| if (change) { |
| tpm_tis_raise_irq(s, tis->active_locty, TPM_TIS_INT_LOCALITY_CHANGED); |
| } |
| } |
| |
| /* abort -- this function switches the locality */ |
| static void tpm_tis_abort(TPMState *s, uint8_t locty) |
| { |
| TPMTISEmuState *tis = &s->s.tis; |
| |
| tis->loc[locty].r_offset = 0; |
| tis->loc[locty].w_offset = 0; |
| |
| DPRINTF("tpm_tis: tis_abort: new active locality is %d\n", tis->next_locty); |
| |
| /* |
| * Need to react differently depending on who's aborting now and |
| * which locality will become active afterwards. |
| */ |
| if (tis->aborting_locty == tis->next_locty) { |
| tis->loc[tis->aborting_locty].state = TPM_TIS_STATE_READY; |
| tis->loc[tis->aborting_locty].sts = TPM_TIS_STS_COMMAND_READY; |
| tpm_tis_raise_irq(s, tis->aborting_locty, TPM_TIS_INT_COMMAND_READY); |
| } |
| |
| /* locality after abort is another one than the current one */ |
| tpm_tis_new_active_locality(s, tis->next_locty); |
| |
| tis->next_locty = TPM_TIS_NO_LOCALITY; |
| /* nobody's aborting a command anymore */ |
| tis->aborting_locty = TPM_TIS_NO_LOCALITY; |
| } |
| |
| /* prepare aborting current command */ |
| static void tpm_tis_prep_abort(TPMState *s, uint8_t locty, uint8_t newlocty) |
| { |
| TPMTISEmuState *tis = &s->s.tis; |
| uint8_t busy_locty; |
| |
| tis->aborting_locty = locty; |
| tis->next_locty = newlocty; /* locality after successful abort */ |
| |
| /* |
| * only abort a command using an interrupt if currently executing |
| * a command AND if there's a valid connection to the vTPM. |
| */ |
| for (busy_locty = 0; busy_locty < TPM_TIS_NUM_LOCALITIES; busy_locty++) { |
| if (tis->loc[busy_locty].state == TPM_TIS_STATE_EXECUTION) { |
| /* |
| * request the backend to cancel. Some backends may not |
| * support it |
| */ |
| tpm_backend_cancel_cmd(s->be_driver); |
| return; |
| } |
| } |
| |
| tpm_tis_abort(s, locty); |
| } |
| |
| static void tpm_tis_receive_bh(void *opaque) |
| { |
| TPMState *s = opaque; |
| TPMTISEmuState *tis = &s->s.tis; |
| uint8_t locty = s->locty_number; |
| |
| tis->loc[locty].sts = TPM_TIS_STS_VALID | TPM_TIS_STS_DATA_AVAILABLE; |
| tis->loc[locty].state = TPM_TIS_STATE_COMPLETION; |
| tis->loc[locty].r_offset = 0; |
| tis->loc[locty].w_offset = 0; |
| |
| if (TPM_TIS_IS_VALID_LOCTY(tis->next_locty)) { |
| tpm_tis_abort(s, locty); |
| } |
| |
| #ifndef RAISE_STS_IRQ |
| tpm_tis_raise_irq(s, locty, TPM_TIS_INT_DATA_AVAILABLE); |
| #else |
| tpm_tis_raise_irq(s, locty, |
| TPM_TIS_INT_DATA_AVAILABLE | TPM_TIS_INT_STS_VALID); |
| #endif |
| } |
| |
| /* |
| * Callback from the TPM to indicate that the response was received. |
| */ |
| static void tpm_tis_receive_cb(TPMState *s, uint8_t locty) |
| { |
| TPMTISEmuState *tis = &s->s.tis; |
| |
| assert(s->locty_number == locty); |
| |
| qemu_bh_schedule(tis->bh); |
| } |
| |
| /* |
| * Read a byte of response data |
| */ |
| static uint32_t tpm_tis_data_read(TPMState *s, uint8_t locty) |
| { |
| TPMTISEmuState *tis = &s->s.tis; |
| uint32_t ret = TPM_TIS_NO_DATA_BYTE; |
| uint16_t len; |
| |
| if ((tis->loc[locty].sts & TPM_TIS_STS_DATA_AVAILABLE)) { |
| len = tpm_tis_get_size_from_buffer(&tis->loc[locty].r_buffer); |
| |
| ret = tis->loc[locty].r_buffer.buffer[tis->loc[locty].r_offset++]; |
| if (tis->loc[locty].r_offset >= len) { |
| /* got last byte */ |
| tis->loc[locty].sts = TPM_TIS_STS_VALID; |
| #ifdef RAISE_STS_IRQ |
| tpm_tis_raise_irq(s, locty, TPM_TIS_INT_STS_VALID); |
| #endif |
| } |
| DPRINTF("tpm_tis: tpm_tis_data_read byte 0x%02x [%d]\n", |
| ret, tis->loc[locty].r_offset-1); |
| } |
| |
| return ret; |
| } |
| |
| #ifdef DEBUG_TIS |
| static void tpm_tis_dump_state(void *opaque, hwaddr addr) |
| { |
| static const unsigned regs[] = { |
| TPM_TIS_REG_ACCESS, |
| TPM_TIS_REG_INT_ENABLE, |
| TPM_TIS_REG_INT_VECTOR, |
| TPM_TIS_REG_INT_STATUS, |
| TPM_TIS_REG_INTF_CAPABILITY, |
| TPM_TIS_REG_STS, |
| TPM_TIS_REG_DID_VID, |
| TPM_TIS_REG_RID, |
| 0xfff}; |
| int idx; |
| uint8_t locty = tpm_tis_locality_from_addr(addr); |
| hwaddr base = addr & ~0xfff; |
| TPMState *s = opaque; |
| TPMTISEmuState *tis = &s->s.tis; |
| |
| DPRINTF("tpm_tis: active locality : %d\n" |
| "tpm_tis: state of locality %d : %d\n" |
| "tpm_tis: register dump:\n", |
| tis->active_locty, |
| locty, tis->loc[locty].state); |
| |
| for (idx = 0; regs[idx] != 0xfff; idx++) { |
| DPRINTF("tpm_tis: 0x%04x : 0x%08x\n", regs[idx], |
| (uint32_t)tpm_tis_mmio_read(opaque, base + regs[idx], 4)); |
| } |
| |
| DPRINTF("tpm_tis: read offset : %d\n" |
| "tpm_tis: result buffer : ", |
| tis->loc[locty].r_offset); |
| for (idx = 0; |
| idx < tpm_tis_get_size_from_buffer(&tis->loc[locty].r_buffer); |
| idx++) { |
| DPRINTF("%c%02x%s", |
| tis->loc[locty].r_offset == idx ? '>' : ' ', |
| tis->loc[locty].r_buffer.buffer[idx], |
| ((idx & 0xf) == 0xf) ? "\ntpm_tis: " : ""); |
| } |
| DPRINTF("\n" |
| "tpm_tis: write offset : %d\n" |
| "tpm_tis: request buffer: ", |
| tis->loc[locty].w_offset); |
| for (idx = 0; |
| idx < tpm_tis_get_size_from_buffer(&tis->loc[locty].w_buffer); |
| idx++) { |
| DPRINTF("%c%02x%s", |
| tis->loc[locty].w_offset == idx ? '>' : ' ', |
| tis->loc[locty].w_buffer.buffer[idx], |
| ((idx & 0xf) == 0xf) ? "\ntpm_tis: " : ""); |
| } |
| DPRINTF("\n"); |
| } |
| #endif |
| |
| /* |
| * Read a register of the TIS interface |
| * See specs pages 33-63 for description of the registers |
| */ |
| static uint64_t tpm_tis_mmio_read(void *opaque, hwaddr addr, |
| unsigned size) |
| { |
| TPMState *s = opaque; |
| TPMTISEmuState *tis = &s->s.tis; |
| uint16_t offset = addr & 0xffc; |
| uint8_t shift = (addr & 0x3) * 8; |
| uint32_t val = 0xffffffff; |
| uint8_t locty = tpm_tis_locality_from_addr(addr); |
| uint32_t avail; |
| |
| if (tpm_backend_had_startup_error(s->be_driver)) { |
| return val; |
| } |
| |
| switch (offset) { |
| case TPM_TIS_REG_ACCESS: |
| /* never show the SEIZE flag even though we use it internally */ |
| val = tis->loc[locty].access & ~TPM_TIS_ACCESS_SEIZE; |
| /* the pending flag is always calculated */ |
| if (tpm_tis_check_request_use_except(s, locty)) { |
| val |= TPM_TIS_ACCESS_PENDING_REQUEST; |
| } |
| val |= !tpm_backend_get_tpm_established_flag(s->be_driver); |
| break; |
| case TPM_TIS_REG_INT_ENABLE: |
| val = tis->loc[locty].inte; |
| break; |
| case TPM_TIS_REG_INT_VECTOR: |
| val = tis->irq_num; |
| break; |
| case TPM_TIS_REG_INT_STATUS: |
| val = tis->loc[locty].ints; |
| break; |
| case TPM_TIS_REG_INTF_CAPABILITY: |
| val = TPM_TIS_CAPABILITIES_SUPPORTED; |
| break; |
| case TPM_TIS_REG_STS: |
| if (tis->active_locty == locty) { |
| if ((tis->loc[locty].sts & TPM_TIS_STS_DATA_AVAILABLE)) { |
| val = TPM_TIS_BURST_COUNT( |
| tpm_tis_get_size_from_buffer(&tis->loc[locty].r_buffer) |
| - tis->loc[locty].r_offset) | tis->loc[locty].sts; |
| } else { |
| avail = tis->loc[locty].w_buffer.size |
| - tis->loc[locty].w_offset; |
| /* |
| * byte-sized reads should not return 0x00 for 0x100 |
| * available bytes. |
| */ |
| if (size == 1 && avail > 0xff) { |
| avail = 0xff; |
| } |
| val = TPM_TIS_BURST_COUNT(avail) | tis->loc[locty].sts; |
| } |
| } |
| break; |
| case TPM_TIS_REG_DATA_FIFO: |
| if (tis->active_locty == locty) { |
| switch (tis->loc[locty].state) { |
| case TPM_TIS_STATE_COMPLETION: |
| val = tpm_tis_data_read(s, locty); |
| break; |
| default: |
| val = TPM_TIS_NO_DATA_BYTE; |
| break; |
| } |
| } |
| break; |
| case TPM_TIS_REG_DID_VID: |
| val = (TPM_TIS_TPM_DID << 16) | TPM_TIS_TPM_VID; |
| break; |
| case TPM_TIS_REG_RID: |
| val = TPM_TIS_TPM_RID; |
| break; |
| #ifdef DEBUG_TIS |
| case TPM_TIS_REG_DEBUG: |
| tpm_tis_dump_state(opaque, addr); |
| break; |
| #endif |
| } |
| |
| if (shift) { |
| val >>= shift; |
| } |
| |
| DPRINTF("tpm_tis: read.%u(%08x) = %08x\n", size, (int)addr, (uint32_t)val); |
| |
| return val; |
| } |
| |
| /* |
| * Write a value to a register of the TIS interface |
| * See specs pages 33-63 for description of the registers |
| */ |
| static void tpm_tis_mmio_write_intern(void *opaque, hwaddr addr, |
| uint64_t val, unsigned size, |
| bool hw_access) |
| { |
| TPMState *s = opaque; |
| TPMTISEmuState *tis = &s->s.tis; |
| uint16_t off = addr & 0xfff; |
| uint8_t locty = tpm_tis_locality_from_addr(addr); |
| uint8_t active_locty, l; |
| int c, set_new_locty = 1; |
| uint16_t len; |
| |
| DPRINTF("tpm_tis: write.%u(%08x) = %08x\n", size, (int)addr, (uint32_t)val); |
| |
| if (locty == 4 && !hw_access) { |
| DPRINTF("tpm_tis: Access to locality 4 only allowed from hardware\n"); |
| return; |
| } |
| |
| if (tpm_backend_had_startup_error(s->be_driver)) { |
| return; |
| } |
| |
| switch (off) { |
| case TPM_TIS_REG_ACCESS: |
| |
| if ((val & TPM_TIS_ACCESS_SEIZE)) { |
| val &= ~(TPM_TIS_ACCESS_REQUEST_USE | |
| TPM_TIS_ACCESS_ACTIVE_LOCALITY); |
| } |
| |
| active_locty = tis->active_locty; |
| |
| if ((val & TPM_TIS_ACCESS_ACTIVE_LOCALITY)) { |
| /* give up locality if currently owned */ |
| if (tis->active_locty == locty) { |
| DPRINTF("tpm_tis: Releasing locality %d\n", locty); |
| |
| uint8_t newlocty = TPM_TIS_NO_LOCALITY; |
| /* anybody wants the locality ? */ |
| for (c = TPM_TIS_NUM_LOCALITIES - 1; c >= 0; c--) { |
| if ((tis->loc[c].access & TPM_TIS_ACCESS_REQUEST_USE)) { |
| DPRINTF("tpm_tis: Locality %d requests use.\n", c); |
| newlocty = c; |
| break; |
| } |
| } |
| DPRINTF("tpm_tis: TPM_TIS_ACCESS_ACTIVE_LOCALITY: " |
| "Next active locality: %d\n", |
| newlocty); |
| |
| if (TPM_TIS_IS_VALID_LOCTY(newlocty)) { |
| set_new_locty = 0; |
| tpm_tis_prep_abort(s, locty, newlocty); |
| } else { |
| active_locty = TPM_TIS_NO_LOCALITY; |
| } |
| } else { |
| /* not currently the owner; clear a pending request */ |
| tis->loc[locty].access &= ~TPM_TIS_ACCESS_REQUEST_USE; |
| } |
| } |
| |
| if ((val & TPM_TIS_ACCESS_BEEN_SEIZED)) { |
| tis->loc[locty].access &= ~TPM_TIS_ACCESS_BEEN_SEIZED; |
| } |
| |
| if ((val & TPM_TIS_ACCESS_SEIZE)) { |
| /* |
| * allow seize if a locality is active and the requesting |
| * locality is higher than the one that's active |
| * OR |
| * allow seize for requesting locality if no locality is |
| * active |
| */ |
| while ((TPM_TIS_IS_VALID_LOCTY(tis->active_locty) && |
| locty > tis->active_locty) || |
| !TPM_TIS_IS_VALID_LOCTY(tis->active_locty)) { |
| bool higher_seize = FALSE; |
| |
| /* already a pending SEIZE ? */ |
| if ((tis->loc[locty].access & TPM_TIS_ACCESS_SEIZE)) { |
| break; |
| } |
| |
| /* check for ongoing seize by a higher locality */ |
| for (l = locty + 1; l < TPM_TIS_NUM_LOCALITIES; l++) { |
| if ((tis->loc[l].access & TPM_TIS_ACCESS_SEIZE)) { |
| higher_seize = TRUE; |
| break; |
| } |
| } |
| |
| if (higher_seize) { |
| break; |
| } |
| |
| /* cancel any seize by a lower locality */ |
| for (l = 0; l < locty - 1; l++) { |
| tis->loc[l].access &= ~TPM_TIS_ACCESS_SEIZE; |
| } |
| |
| tis->loc[locty].access |= TPM_TIS_ACCESS_SEIZE; |
| DPRINTF("tpm_tis: TPM_TIS_ACCESS_SEIZE: " |
| "Locality %d seized from locality %d\n", |
| locty, tis->active_locty); |
| DPRINTF("tpm_tis: TPM_TIS_ACCESS_SEIZE: Initiating abort.\n"); |
| set_new_locty = 0; |
| tpm_tis_prep_abort(s, tis->active_locty, locty); |
| break; |
| } |
| } |
| |
| if ((val & TPM_TIS_ACCESS_REQUEST_USE)) { |
| if (tis->active_locty != locty) { |
| if (TPM_TIS_IS_VALID_LOCTY(tis->active_locty)) { |
| tis->loc[locty].access |= TPM_TIS_ACCESS_REQUEST_USE; |
| } else { |
| /* no locality active -> make this one active now */ |
| active_locty = locty; |
| } |
| } |
| } |
| |
| if (set_new_locty) { |
| tpm_tis_new_active_locality(s, active_locty); |
| } |
| |
| break; |
| case TPM_TIS_REG_INT_ENABLE: |
| if (tis->active_locty != locty) { |
| break; |
| } |
| |
| tis->loc[locty].inte = (val & (TPM_TIS_INT_ENABLED | |
| TPM_TIS_INT_POLARITY_MASK | |
| TPM_TIS_INTERRUPTS_SUPPORTED)); |
| break; |
| case TPM_TIS_REG_INT_VECTOR: |
| /* hard wired -- ignore */ |
| break; |
| case TPM_TIS_REG_INT_STATUS: |
| if (tis->active_locty != locty) { |
| break; |
| } |
| |
| /* clearing of interrupt flags */ |
| if (((val & TPM_TIS_INTERRUPTS_SUPPORTED)) && |
| (tis->loc[locty].ints & TPM_TIS_INTERRUPTS_SUPPORTED)) { |
| tis->loc[locty].ints &= ~val; |
| if (tis->loc[locty].ints == 0) { |
| qemu_irq_lower(tis->irq); |
| DPRINTF("tpm_tis: Lowering IRQ\n"); |
| } |
| } |
| tis->loc[locty].ints &= ~(val & TPM_TIS_INTERRUPTS_SUPPORTED); |
| break; |
| case TPM_TIS_REG_STS: |
| if (tis->active_locty != locty) { |
| break; |
| } |
| |
| val &= (TPM_TIS_STS_COMMAND_READY | TPM_TIS_STS_TPM_GO | |
| TPM_TIS_STS_RESPONSE_RETRY); |
| |
| if (val == TPM_TIS_STS_COMMAND_READY) { |
| switch (tis->loc[locty].state) { |
| |
| case TPM_TIS_STATE_READY: |
| tis->loc[locty].w_offset = 0; |
| tis->loc[locty].r_offset = 0; |
| break; |
| |
| case TPM_TIS_STATE_IDLE: |
| tis->loc[locty].sts = TPM_TIS_STS_COMMAND_READY; |
| tis->loc[locty].state = TPM_TIS_STATE_READY; |
| tpm_tis_raise_irq(s, locty, TPM_TIS_INT_COMMAND_READY); |
| break; |
| |
| case TPM_TIS_STATE_EXECUTION: |
| case TPM_TIS_STATE_RECEPTION: |
| /* abort currently running command */ |
| DPRINTF("tpm_tis: %s: Initiating abort.\n", |
| __func__); |
| tpm_tis_prep_abort(s, locty, locty); |
| break; |
| |
| case TPM_TIS_STATE_COMPLETION: |
| tis->loc[locty].w_offset = 0; |
| tis->loc[locty].r_offset = 0; |
| /* shortcut to ready state with C/R set */ |
| tis->loc[locty].state = TPM_TIS_STATE_READY; |
| if (!(tis->loc[locty].sts & TPM_TIS_STS_COMMAND_READY)) { |
| tis->loc[locty].sts = TPM_TIS_STS_COMMAND_READY; |
| tpm_tis_raise_irq(s, locty, TPM_TIS_INT_COMMAND_READY); |
| } |
| tis->loc[locty].sts &= ~(TPM_TIS_STS_DATA_AVAILABLE); |
| break; |
| |
| } |
| } else if (val == TPM_TIS_STS_TPM_GO) { |
| switch (tis->loc[locty].state) { |
| case TPM_TIS_STATE_RECEPTION: |
| if ((tis->loc[locty].sts & TPM_TIS_STS_EXPECT) == 0) { |
| tpm_tis_tpm_send(s, locty); |
| } |
| break; |
| default: |
| /* ignore */ |
| break; |
| } |
| } else if (val == TPM_TIS_STS_RESPONSE_RETRY) { |
| switch (tis->loc[locty].state) { |
| case TPM_TIS_STATE_COMPLETION: |
| tis->loc[locty].r_offset = 0; |
| tis->loc[locty].sts = TPM_TIS_STS_VALID | |
| TPM_TIS_STS_DATA_AVAILABLE; |
| break; |
| default: |
| /* ignore */ |
| break; |
| } |
| } |
| break; |
| case TPM_TIS_REG_DATA_FIFO: |
| /* data fifo */ |
| if (tis->active_locty != locty) { |
| break; |
| } |
| |
| if (tis->loc[locty].state == TPM_TIS_STATE_IDLE || |
| tis->loc[locty].state == TPM_TIS_STATE_EXECUTION || |
| tis->loc[locty].state == TPM_TIS_STATE_COMPLETION) { |
| /* drop the byte */ |
| } else { |
| DPRINTF("tpm_tis: Byte to send to TPM: %02x\n", (uint8_t)val); |
| if (tis->loc[locty].state == TPM_TIS_STATE_READY) { |
| tis->loc[locty].state = TPM_TIS_STATE_RECEPTION; |
| tis->loc[locty].sts = TPM_TIS_STS_EXPECT | TPM_TIS_STS_VALID; |
| } |
| |
| if ((tis->loc[locty].sts & TPM_TIS_STS_EXPECT)) { |
| if (tis->loc[locty].w_offset < tis->loc[locty].w_buffer.size) { |
| tis->loc[locty].w_buffer. |
| buffer[tis->loc[locty].w_offset++] = (uint8_t)val; |
| } else { |
| tis->loc[locty].sts = TPM_TIS_STS_VALID; |
| } |
| } |
| |
| /* check for complete packet */ |
| if (tis->loc[locty].w_offset > 5 && |
| (tis->loc[locty].sts & TPM_TIS_STS_EXPECT)) { |
| /* we have a packet length - see if we have all of it */ |
| #ifdef RAISE_STS_IRQ |
| bool needIrq = !(tis->loc[locty].sts & TPM_TIS_STS_VALID); |
| #endif |
| len = tpm_tis_get_size_from_buffer(&tis->loc[locty].w_buffer); |
| if (len > tis->loc[locty].w_offset) { |
| tis->loc[locty].sts = TPM_TIS_STS_EXPECT | |
| TPM_TIS_STS_VALID; |
| } else { |
| /* packet complete */ |
| tis->loc[locty].sts = TPM_TIS_STS_VALID; |
| } |
| #ifdef RAISE_STS_IRQ |
| if (needIrq) { |
| tpm_tis_raise_irq(s, locty, TPM_TIS_INT_STS_VALID); |
| } |
| #endif |
| } |
| } |
| break; |
| } |
| } |
| |
| static void tpm_tis_mmio_write(void *opaque, hwaddr addr, |
| uint64_t val, unsigned size) |
| { |
| return tpm_tis_mmio_write_intern(opaque, addr, val, size, false); |
| } |
| |
| static const MemoryRegionOps tpm_tis_memory_ops = { |
| .read = tpm_tis_mmio_read, |
| .write = tpm_tis_mmio_write, |
| .endianness = DEVICE_LITTLE_ENDIAN, |
| .valid = { |
| .min_access_size = 1, |
| .max_access_size = 4, |
| }, |
| }; |
| |
| static int tpm_tis_do_startup_tpm(TPMState *s) |
| { |
| return tpm_backend_startup_tpm(s->be_driver); |
| } |
| |
| /* |
| * This function is called when the machine starts, resets or due to |
| * S3 resume. |
| */ |
| static void tpm_tis_reset(DeviceState *dev) |
| { |
| TPMState *s = TPM(dev); |
| TPMTISEmuState *tis = &s->s.tis; |
| int c; |
| |
| tpm_backend_reset(s->be_driver); |
| |
| tis->active_locty = TPM_TIS_NO_LOCALITY; |
| tis->next_locty = TPM_TIS_NO_LOCALITY; |
| tis->aborting_locty = TPM_TIS_NO_LOCALITY; |
| |
| for (c = 0; c < TPM_TIS_NUM_LOCALITIES; c++) { |
| tis->loc[c].access = TPM_TIS_ACCESS_TPM_REG_VALID_STS; |
| tis->loc[c].sts = 0; |
| tis->loc[c].inte = TPM_TIS_INT_POLARITY_LOW_LEVEL; |
| tis->loc[c].ints = 0; |
| tis->loc[c].state = TPM_TIS_STATE_IDLE; |
| |
| tis->loc[c].w_offset = 0; |
| tpm_backend_realloc_buffer(s->be_driver, &tis->loc[c].w_buffer); |
| tis->loc[c].r_offset = 0; |
| tpm_backend_realloc_buffer(s->be_driver, &tis->loc[c].r_buffer); |
| } |
| |
| tpm_tis_do_startup_tpm(s); |
| } |
| |
| static const VMStateDescription vmstate_tpm_tis = { |
| .name = "tpm", |
| .unmigratable = 1, |
| }; |
| |
| static Property tpm_tis_properties[] = { |
| DEFINE_PROP_UINT32("irq", TPMState, |
| s.tis.irq_num, TPM_TIS_IRQ), |
| DEFINE_PROP_STRING("tpmdev", TPMState, backend), |
| DEFINE_PROP_END_OF_LIST(), |
| }; |
| |
| static void tpm_tis_realizefn(DeviceState *dev, Error **errp) |
| { |
| TPMState *s = TPM(dev); |
| TPMTISEmuState *tis = &s->s.tis; |
| |
| s->be_driver = qemu_find_tpm(s->backend); |
| if (!s->be_driver) { |
| error_setg(errp, "tpm_tis: backend driver with id %s could not be " |
| "found", s->backend); |
| return; |
| } |
| |
| s->be_driver->fe_model = TPM_MODEL_TPM_TIS; |
| |
| if (tpm_backend_init(s->be_driver, s, tpm_tis_receive_cb)) { |
| error_setg(errp, "tpm_tis: backend driver with id %s could not be " |
| "initialized", s->backend); |
| return; |
| } |
| |
| if (tis->irq_num > 15) { |
| error_setg(errp, "tpm_tis: IRQ %d for TPM TIS is outside valid range " |
| "of 0 to 15.\n", tis->irq_num); |
| return; |
| } |
| |
| tis->bh = qemu_bh_new(tpm_tis_receive_bh, s); |
| |
| isa_init_irq(&s->busdev, &tis->irq, tis->irq_num); |
| } |
| |
| static void tpm_tis_initfn(Object *obj) |
| { |
| ISADevice *dev = ISA_DEVICE(obj); |
| TPMState *s = TPM(obj); |
| |
| memory_region_init_io(&s->mmio, OBJECT(s), &tpm_tis_memory_ops, |
| s, "tpm-tis-mmio", |
| TPM_TIS_NUM_LOCALITIES << TPM_TIS_LOCALITY_SHIFT); |
| memory_region_add_subregion(isa_address_space(dev), TPM_TIS_ADDR_BASE, |
| &s->mmio); |
| } |
| |
| static void tpm_tis_uninitfn(Object *obj) |
| { |
| TPMState *s = TPM(obj); |
| |
| memory_region_del_subregion(get_system_memory(), &s->mmio); |
| memory_region_destroy(&s->mmio); |
| } |
| |
| static void tpm_tis_class_init(ObjectClass *klass, void *data) |
| { |
| DeviceClass *dc = DEVICE_CLASS(klass); |
| |
| dc->realize = tpm_tis_realizefn; |
| dc->props = tpm_tis_properties; |
| dc->reset = tpm_tis_reset; |
| dc->vmsd = &vmstate_tpm_tis; |
| } |
| |
| static const TypeInfo tpm_tis_info = { |
| .name = TYPE_TPM_TIS, |
| .parent = TYPE_ISA_DEVICE, |
| .instance_size = sizeof(TPMState), |
| .instance_init = tpm_tis_initfn, |
| .instance_finalize = tpm_tis_uninitfn, |
| .class_init = tpm_tis_class_init, |
| }; |
| |
| static void tpm_tis_register(void) |
| { |
| type_register_static(&tpm_tis_info); |
| tpm_register_model(TPM_MODEL_TPM_TIS); |
| } |
| |
| type_init(tpm_tis_register) |
