blob: dc57f076b5de5f13cf79d7c63883e6b9b95d54d6 [file] [log] [blame] [edit]
TCG Interpreter (TCI) - Copyright (c) 2011 Stefan Weil.
This file is released under the BSD license.
1) Introduction
TCG (Tiny Code Generator) is a code generator which translates
code fragments ("basic blocks") from target code (any of the
targets supported by QEMU) to a code representation which
can be run on a host.
QEMU can create native code for some hosts (arm, hppa, i386, ia64, ppc, ppc64,
s390, sparc, x86_64). For others, unofficial host support was written.
By adding a code generator for a virtual machine and using an
interpreter for the generated bytecode, it is possible to
support (almost) any host.
This is what TCI (Tiny Code Interpreter) does.
2) Implementation
Like each TCG host frontend, TCI implements the code generator in
tcg-target.c, tcg-target.h. Both files are in directory tcg/tci.
The additional file tcg/tci.c adds the interpreter.
The bytecode consists of opcodes (same numeric values as those used by
TCG), command length and arguments of variable size and number.
3) Usage
For hosts without native TCG, the interpreter TCI must be enabled by
configure --enable-tcg-interpreter
If configure is called without --enable-tcg-interpreter, it will
suggest using this option. Setting it automatically would need
additional code in configure which must be fixed when new native TCG
implementations are added.
System emulation should work on any 32 or 64 bit host.
User mode emulation might work. Maybe a new linker script (*.ld)
is needed. Byte order might be wrong (on big endian hosts)
and need fixes in configure.
For hosts with native TCG, the interpreter TCI can be enabled by
configure --enable-tcg-interpreter
The only difference from running QEMU with TCI to running without TCI
should be speed. Especially during development of TCI, it was very
useful to compare runs with and without TCI. Create /tmp/qemu.log by
qemu-system-i386 -d in_asm,op_opt,cpu -D /tmp/qemu.log -singlestep
once with interpreter and once without interpreter and compare the resulting
qemu.log files. This is also useful to see the effects of additional
registers or additional opcodes (it is easy to modify the virtual machine).
It can also be used to verify native TCGs.
Hosts with native TCG can also enable TCI by claiming to be unsupported:
configure --cpu=unknown --enable-tcg-interpreter
configure then no longer uses the native linker script (*.ld) for
user mode emulation.
4) Status
TCI needs special implementation for 32 and 64 bit host, 32 and 64 bit target,
host and target with same or different endianness.
| host (le) host (be)
| 32 64 32 64
------------+------------------------------------------------------------
target (le) | s0, u0 s1, u1 s?, u? s?, u?
32 bit |
|
target (le) | sc, uc s1, u1 s?, u? s?, u?
64 bit |
|
target (be) | sc, u0 sc, uc s?, u? s?, u?
32 bit |
|
target (be) | sc, uc sc, uc s?, u? s?, u?
64 bit |
|
System emulation
s? = untested
sc = compiles
s0 = bios works
s1 = grub works
s2 = Linux boots
Linux user mode emulation
u? = untested
uc = compiles
u0 = static hello works
u1 = linux-user-test works
5) Todo list
* TCI is not widely tested. It was written and tested on a x86_64 host
running i386 and x86_64 system emulation and Linux user mode.
A cross compiled QEMU for i386 host also works with the same basic tests.
A cross compiled QEMU for mipsel host works, too. It is terribly slow
because I run it in a mips malta emulation, so it is an interpreted
emulation in an emulation.
A cross compiled QEMU for arm host works (tested with pc bios).
A cross compiled QEMU for ppc host works at least partially:
i386-linux-user/qemu-i386 can run a simple hello-world program
(tested in a ppc emulation).
* Some TCG opcodes are either missing in the code generator and/or
in the interpreter. These opcodes raise a runtime exception, so it is
possible to see where code must be added.
* The pseudo code is not optimized and still ugly. For hosts with special
alignment requirements, it needs some fixes (maybe aligned bytecode
would also improve speed for hosts which support byte alignment).
* A better disassembler for the pseudo code would be nice (a very primitive
disassembler is included in tcg-target.c).
* It might be useful to have a runtime option which selects the native TCG
or TCI, so QEMU would have to include two TCGs. Today, selecting TCI
is a configure option, so you need two compilations of QEMU.